Water Filter Maintenance and Signs of Faults
Maintaining a water filter means replacing the filters on time, checking the tank and connections, and measuring the TDS of the filtered water. You can keep an eye on some of this yourself at home. Below we have set out what you can do yourself and which signs mean it is time to call a technician.
What you can do at home
- Make a note of the replacement date. Write the date of the last filter replacement on the system or in your phone. Pre-filters are usually replaced every 6 months, the membrane every 12–18 months.
- Look under the sink once a month. Check for damp on the floor of the cupboard, puddles under the system or drips at the connections.
- Clean the end of the tap. Deposits can build up over time in the strainer at the end of the filtered water tap; it can be unscrewed and rinsed.
- Drain the tank after a long break. After a holiday or a break of a few weeks, drain the first water sitting in the tank and let the tank refill.
- Measure TDS if you can. If you have a TDS meter at home, measure the filtered water once a month and note the result. A value that rises over time shows the membrane is wearing out.
Signs of a fault and likely causes
| Sign | Likely cause | What to do |
|---|---|---|
| Water trickles out, tank is slow to fill | A clogged pre-filter, low mains water pressure or a drop in the tank's air pressure | Check the filter replacement date; have it checked by a technician |
| The system sends water to the drain non-stop | A faulty automatic shut-off valve or check valve, low pressure | Have it checked by a technician; it pushes up your water bill |
| Damp under the sink | A loose fitting, a crushed seal or a cracked housing | Close the inlet valve straight away and call a technician |
| The water tastes or smells different | A clogged post-carbon filter or water left standing in the tank for a long time | Drain the tank; if that does not help, replace the filters |
| The TDS of the filtered water has risen | A worn membrane or a connection problem | Membrane check |
| The pump has become louder or runs even when the tank is full | A faulty pressure switch or pump | Have it checked by a technician |
| The tap drips | Tap seal | Seal replacement |
If you suspect a leak, the first thing to do is close the inlet valve that connects the system to the cold water line. With the valve closed, no water reaches the system and your kitchen is safe until the technician arrives.
Why does the tank start giving less water?
Inside a water filter tank there is an air chamber that pushes the water towards the tap. The air pressure in this chamber drops over time. When it does, little water comes out of the tap even if the tank looks full. We check the tank during maintenance too: if the air pressure has dropped, it is set to the value recommended by the manufacturer; if the air chamber has failed, the tank is replaced.
What is checked inside the system during maintenance?
On a maintenance visit, besides replacing the filters, we check: the condition of the filter housings and seals, all fittings for leaks, the tank's air pressure, the automatic shut-off valve, and on systems with a pump, the pump and pressure switches. Finally, we measure the TDS of the filtered water and show you the result.




We show how filters are replaced step by step, with photos, in our article How to replace water filters.
What happens without maintenance?
Clogged pre-filters slow the flow of water and let chlorine reach the membrane, which then wears out early. When the membrane is worn, the TDS of the filtered water rises and limescale comes back in the kettle. In systems left without maintenance for a long time, the water standing in the tank and tubing starts to taste bad. In short, maintenance determines both the quality of the water and the life of the system.
How long does maintenance take, and what does it cost?
Maintenance done together with a filter replacement takes about 30 minutes at your home. Filter replacement starts from 1200 TL. We also service other brands; just send us the make and model of your system on WhatsApp. Details are on our filter replacement page.
Questions about water filter maintenance
How often should a water filter be serviced?
We recommend a service every 6 months, when the pre-filters are replaced. On this visit the connections, the tank and the pump, if there is one, are also checked.
Why does my water filter keep running water to the drain?
If the system sends water to the drain non-stop, the automatic shut-off valve or the check valve may have failed; low pressure can also cause it. As it will push up your water bill, you should have it checked.
My water filter is leaking. What should I do?
First close the inlet valve that connects the system to the cold water line. Then call a technician; a leak usually comes from a loose fitting or a crushed seal.
Do you service other brands?
Yes. Send us the make and model of your system, or a photo, and we will come with the right filters.
More guides
- How to Replace Water FiltersThe eight steps of a filter change, from turning off the water to the TDS test, with photos we took on real jobs.
- What Is a Membrane Filter and When Should It Be Replaced?How does a reverse osmosis membrane work, what does it remove, why does it wear out and how can you tell it is time to replace it?
- Can You Add a Pump to a Water Filter?Signs of low pressure, how a booster pump works, and whether to add a pump or buy a unit with one built in.
Let us service your system
Filter replacement from 1200 TL. During maintenance we check the connections, the tank and the TDS of your water.

